Wednesday, September 20, 2017

30ft - Superflex Alpha Systems RV Camper Rubber Roof Kit classAcustoms






The SUPERFLEX roofing system is the most sate-of-the-art membrane roof system on the market today.
SUPERFLEX roofing membrane is used in conjunction with Alpha's water based adhesive and solvent based sealants,  having been specifically engineered to provide premium performance and flexibility for the demanding roof designs of today's RV.

Take a look at the benefits of switching from EPDM to SuperFlex Roofing.

Kit will ship in two boxes and Includes:
  • 15 Feet x 8 1/2 Feet SuperFlex Roofing Roll - Folded
  • 4 tubes of Alpha Systems 1021 Self Leveling Sealant (11 oz)
  • 2 Rolls of Butyl Putty Tape (1/8" Thick x 3/4" W x 30' L)
  • 1 Gallon of Alpha Systems Rubber Roof Adhesive (8010)
Features & Specifications SuperFlex Roofing Roll:
  • Single-ply membrane that is approximately half of the weight of EPDM
  • .165 lbs/sq feet compared to EPDM at .29 lbs/sq foot
  • Will not chalk, fade, or leave streaks down the side of your RV
  • Brilliant UV performance and is resistant to mold, algae, and fungus
  • Better puncture resistance than EPDM at .028 Thick
  • Non-skid surface for better traction. Install roofing with smooth side down, facing glue.
  • Color is same throughout substrate
  • Will not shrink or crack (100% solids sealant)
  • Stretches easier so you can get a perfect, tight fit
  • Can be easily repaired.

Features & Specifications Alpha Systems 1021 Self Leveling Sealant:
  • 1021 HIGH SOLIDS SEALANT is a one part all weather self-leveling sealant designed and formulated to provide excellent weather resistance.
  • It features high solids, low V.O.C. content, and no hazardous air pollutants (HAP).
  • This compound provides good adhesion to a variety of substrates.
  • This product has good low temperature resistance and will not crack at -40oF.
  • Typically used in RV applications where a long-term weather tight seal with good ozone and UV resistance are required.
  • Cured sealant is paintable.
  • Surfaces should be free of dirt, oil, or other contaminants. A solvent cleaned surface is optimum.
  • BASE: EPDM
  • SOLVENT:   Heptane
  • VISCOSITY:  80,000 - 200,000 cps
  • COVERAGE:  380 lineal ft/gal
  • COLOR: White
  • MINIMUM APPLICATION TEMP: 60ËšF
  • CAUTION:  THIS MATERIAL MAY BE HARMFUL OR FATAL IF SWALLOWED.  IF SWALLOWED, DO NOT INDUCE VOMITING.  CALL A PHYSICIAN.  THIS MATERIAL IN THE LIQUID OR VAPOR PHASES IS EXTREMELY FLAMMABLE. KEEP AWAY FROM SPARKS OR OPEN FLAME.  DON'T SMOKE.Prolonged breathing of vapors may cause headaches and even unconsciousness. Avoid prolonged breathing and use good ventilation.
Features & Specifications Butyl Putty Tape:
  • Non-hardening, pliable butyl putty tape.
  • COLOR: Gray
  • Waterproofs overlapping metal seams.
  • Butyl tape is the only putty tape recommended for use in direct contact with EPDM (rubber) roofing material, as regular "putty tape" oozes petroleum products which can damage EPDM.
  • 1/8" high X 3/4" wide - Roll 30 feet long
Features & Specifications Alpha Systems 8010 Adhesive:
  • 8010 is a technically advanced scientific formula of water base adhesive designed for use as a bonding adhesive for single ply roofing membranes.
  • DESIGNED TO BOND: EPDM, PVC, and Hypalon to wood fiberboard, plywood, EPS, any typical polyisocyanurate insulation, gypsum, concrete, etc.
  • 8010 may be applied by spray, roll coating, or by brush.
  • Grows stronger and adhears more with age.
  • Remains flexible to compensate for expansion and contraction of the membrane itself.
  • COLOR: White
  • SOLVENT: Water Based
  • ADHESIVE TYPE: Modified Acrylic
  • COLOR: White
  • COVERAGE: 160-200 sq ft/gal (1side @ 8-10 mil)
  • NET WEIGHT: 8.50 lbs/gal
  • SOLIDS CONTENT: 68%
  • VISCOSITY: 10,000-15,000 cps (Brookfield RVF)
  • 8010 may be applied by spray, roll coating, or by brush.
    (When using spray application an Aro 650095 4.25 inch air motor with a 30:1 ration pump @ 80 psi using a 651-500 gun equipped with #651551 quick clean and spray tip #T.C. 1565 with 0.015 orifice or similar equipment is recommended).
  • For maximum bond strength a two-sided application is recommended.
    If one surface is porous, such as plywood or fiberboard, it is acceptable to wet laminate the membrane to the substrate.
    If both surfaces are non-porous, such as EPS or ISO apply the adhesive to both surfaces 4 - 5 mils and allow to dry approximately 20 - 30 minutes, depending on conditions.
  • Adhesive will turn from white to clear when it is dry.
  • Apply membrane to roof deck and roll or broom down sheet to assure 100% contact area.
  • DO NOT FREEZE - KEEP OUT OF REACH OF CHILDREN
Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
 
Call Us: (574) 206-0101


Friday, September 8, 2017

LED Submersible SQ Trailer Light Kit Under 80" Stop / Turn / Tail Boat Trailer classAcustoms





LED Submersible SQ Trailer Light Kit Under 80" Stop / Turn / Tail Boat Trailer classAcustoms

12 volt: You can not put this in a house or plug into a wall - 110/115/220 volt will damage the unit.
DOT APPROVED
Includes both rear trailer tail lights
mounting clips, and wire connectors
Submersible & Sealed Capsule Design for protection against harsh salt water environment
Complete Submersible LED Light Kit for trailers under 80" 
25 foot trailer wiring harness
Includes both rear trailer tail lights
plastic license plate holder
Street side has 18 diodes
Curb side has 14 diodes

Measurements:
4 1/2" x 5 1/2" x 3"  


Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
 
Call Us: (574) 206-0101


LED Submersible SQ RV Trailer Light Kit Over 80" Stop / Turn / Tail Boat classacustoms






12 volt
DOT Approved
Waterproof LED Tail Lights
LED Marker Lights (2 Amber)
Wire Harness and Wire Connectors
License Bracket
Street side has 20 diodes
Curb side has 16 diodes
Stud mount lights are 2 bolts on 2" centers

Items are purchased in bulk quantities so no retail box.


Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
 
Call Us: (574) 206-0101



Thursday, September 7, 2017

Half Moon Side Vent Cargo Trailer Air Vent 22813 classacustoms

A 3" hole will need to be cut in wall where you wish to place the inner vent piece.
Do not cut wall stud.

The 1/2 moon goes on the outside of your trailer matching up to the round part so the flat side of the 1/2 moon faces your trailer. These can be screwed or riveted on.

To promote airflow throughout trailer install one complete moon vent in upper front corner of trailer and additional moon vent in lower back corner or trailer, see diagram from examples.











Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
 
Call Us: (574) 206-0101


Wednesday, September 6, 2017

Folding Table Leg for RV HG-FL275 classAcustoms








Features & Specifications:

If you have a free standing table you will need two legs.
Powder Coated
Mounting Hardware NOT Included
No retail box as these are purchased in bulk, no install instructions as they are OEM parts.
Measurements:
Legs: 27.5" Overall Length x 15" Wide
Brackets on Legs: 1" x 1 1/4"
Middle Bracket: 2 6/16" x 1 1/2"


Leg needs to be closed when installing to ensure you have the correct angle of the leg for proper closing.







Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
 
Call Us: (574) 206-0101