29 Gallon Fresh / Gray Water Holding Tank | T-2955

Class A Customs 29 Gallon Fresh / Gray Water Holding Tank | T-2955






Tank Measurements +/- .25" on each measurement due to manufacturing process

VIEW CAD DRAWING - SECOND PHOTO

Average tank thickness .219 or 7/32" thick (just under 1/4")

NO Installed Fittings - Tank is BLANK
We offer Uniseal Fittings - Class A Customs does not sell Spin Weld Fittings.

Made In USA Class A Customs manufactures these tanks and is located in Elkhart, Indiana

Fresh and Drinking Water Safe great for rvs, food vendors and extra water storage

BPA Free Class A Customs does not carry this chemical nor uses it in the manufacturing process


NO NSF LOGO Class A Customs NSF Letter (on Water Tank Helps Page) explaining why we no longer have the NSF Logo in our tanks, however, Class A Customs Fresh/Gray Water Tanks are still made from the same NSF Approved Materials.
Forward this letter onto your inspecting Health Department before ordering to be sure tanks will work for your application and get approval.

UV-8 Stabilization

Complies with
U.S. FDA 21 CFR 177.1520 (c)3.1a
Canadian HPFB No Objection
Underwriters Laboratories Inc.
EU, 10/2011
NSF International NSF/ANSI Std 61 (sec 4 & 5)

Non-Pressurized Tank all tanks we carry must be vented, Basic Plumbing Example
Fresh or Gray Water Use ideal for rvs, food vendors and extra water storage
Seamless One-piece seamless construction, no seams to burst
Rotatable tank can be placed on any side
Resistant Stain, Corrosion and Rust Resistant
Color Creamy White in color so you can see waterline through tank
Made From Medium Density Polyethylene (MDPE) Resin - glues do not stick to this material and easily cleaned.

OEM Part
No retail box - no install instructions
Have a certified technician install all parts to prevent product damage and personal injury
Helpful information & answers to common questions can be found on the Water Tank Helps Page

Additional Fittings
To install additional fittings anywhere on the tank we recommend Uniseal Fittings, you can have from .5" up-to 3"
We do not take orders for custom fitting placements or sizes unless bulk ordering, 100 or more of each tank per order.

Preparation
Sanitize each tank prior to use to remove any debris from the manufacturing process
Tanks are made in a warehouse, wipe with a damp cloth to remove surface dust or scuffs


Installation & Plumbing
Non-Pressurized Tank all tanks we carry must be vented allowing air in and out when in use, Plumbing Examples
Do Not hook a garden hose directly to tank damage will occur, it is recommended to use a fill dish or other gravity process
Do Not over-tighten fittings as damage will occur.

It is recommended to use plastic NPT male fittings with plastic female NPT fittings to avoid damaging the threads, metal thread fittings can crush the plastic threads.
Very little, if any, pipe thread tape is needed using too much pipe tape will damage the threads. We do not recommend pipe dope as you can not remove the fitting later, if used be sure to use a food safe brand.



What fittings will I need for my plumbing?
This will depend on how you are setting-up your tank and will vary by application, we are not aware of what items you will be needing, please view the Plumbing Examples



Mounting & Bracing
Tank can be placed on any side.
Place tank on level surface and brace to prevent tank from moving during transit.
Tank needs to be adequately supported, examples on the Water Tank Helps Page
Do Not hang by ratchet straps, this is too thin and will not adequately support tank.
Do Not place weight on tank, if you need to stack the tanks you will need a weight bearing shelf between them.

Can I install the tank under the trailer?
Tanks can be installed inside or outside of unit, for food vendors verify requirements before purchasing as some areas do not allow tanks to be outside of the unit and others do not allow the tank to be inside of the unit.
Be sure to Sanitize Tank before installing.

All tanks must be braced and secured to prevent any movement of the tank while in transit and to prevent possibility of tank tipping or falling.
Due to the manufacturing process all the tanks especially the larger in size will have a bowing to the walls, when the tank is filled the tank will expand out removing the inward bow, we recommend laying all tanks on a level surface (this can be angled to help with drainage) and bracing the tanks. For larger tanks it is recommended to brace all side walls with plywood or metal, we do not recommend using ratchet straps on the tanks alone as this is a large amount of weight on a thin strip and may cause cutting into the tank. For tanks placed outside it is also recommend to enclose tanks using sheet metal / plywood or some other type of weather proof material to prevent damage from road debris and speed bumps, be sure to check your clearance before ordering.

Brackets or Strap Systems Due to the variety of installations we do not carry brackets or bracing systems.




Before you build or modify unit, you need to verify rules and regulations.
Codes vary by local health departments, not state.
We are not aware of the codes or rules. We are not aware of what tanks or items you need.

Ask your inspector BEFORE purchasing
Size Requirements (Gallons / Measurements / Fresh to Gray ratio)
Does the bottom need to be slanted? Can I place the tank on a slanted surface as this would make the tank then slanted?
Fittings Requirements (Size / Placement / Materials)
Filling Procedure Requirements (Lockable Fill Dish / Materials)
Tank Placement Requirements (Inside / Outside of unit)
Clean Out Requirements Do I need a clean out? What size does this need to be?
Class A Customs Tanks have NO NSF LOGO - read below for why


Water Tank Percent Calculation Examples
Multiply (fresh tank size) x 1.15 (1 . 15%) = Tank needed
30 x 1.15 (15%) = 34.50
30 x 1.50 (50%) = 4

NO NSF Logo
Tanks no longer have the NSF logo molded into them due to changes NSF made regarding the use of the NSF logo. The NSF Company does not allow for end users to use the NSF logo unless each item has been inspected and a certification paid for each item, the material that all of our tanks are made from are still the same NSF Certified Material, adding this extra step of certification is an unnecessary step but generates revenues.

The NSF Company does not allow vendors/manufacturers to link to the NSF paperwork unless verified NSF products are being used, our company has been verified and therefore is allowed to link to the NSF Certified Materials on the NSF Website. If needed your inspector can check on this regarding our company and website as we have already provided this information to the NSF company and have been advised on how to correctly use/link to the certification information on our website.


What does my inspector need when I go to inspections on the tanks?
Class A Customs NSF Letter (on Water Tank Helps Page)
Receipt of Purchase
All tanks have the part number molded into the tank, inspector can verify tank.



Custom Water Tanks
We can make a custom tank however due to the cost of a mold ($8,500 and up) most customers needing only a few tanks find it better to use a tank we already manufacture.
For more information and a quote on custom tanks please fill-out our Water Tank Build Form.


Class A Customs
1130 County Road 6 West
Elkhart, IN 46514


Phone: (574) 206-0101





41 Gallon Fresh / Gray Water Holding Tank | T-4159




Tank Measurements +/- .25" on each measurement due to manufacturing process

Average tank thickness .219 or 7/32" thick (just under 1/4")

Installed Fittings See Photos
Two) 1.5" Female NPT Fitting - fitting is sealed to use remove membrane with razor knife
Two) .5" Female NPT Fitting - fitting is open


Class A Customs located in Elkhart, Indiana manufactures fresh and gray water use tanks along with black waste water holding tanks.

great for rvs, food vendors, tiny houses, overlanding and extra water storage


BPA FREE

Class A Customs does not carry this chemical nor uses it in the manufacturing process

Material Used To Manufacture
NSF Certified Materials - No Logo in Tanks
UV-8 Stabilization
glues do not stick to this material and easily cleaned.

Complies with:
U.S. FDA 21 CFR 177.1520 (c)3.1a
Canadian HPFB No Objection
Underwriters Laboratories Inc.
EU, 10/2011
NSF International NSF/ANSI Std 61 (sec 4 & 5)

Class A Customs NSF Letter - this letter has all fresh/gray tank sizes, part #'s, measurements and fittings, along with material tank is made from.

all tanks Class A Customs manufactures must be vented (allow air in/out during use), Plumbing Example and Fill Dishes
Tanks creamy white in color can be used for Fresh or Gray water use, great for rvs, food vendors, tiny houses, over-landing and extra water storage

Seamless
One-piece seamless construction, no seams to burst Average tank thickness: .219 or 7/32" thick (just under 1/4")

Rotatable
tank can be placed on any side but must be braced

Resistant
Stain, Corrosion and Rust Resistant

Color
Creamy White in color so you can see waterline through tank, we recommend a Water Tank Monitor to check levels

Can I stack the water tanks on top of each other?
Can I put weight on the tanks?

No, do not place anything on the tanks, if you need to stack the tanks you will need a weight bearing shelf between them.


Class A Customs
1130 County Road 6 West
Elkhart, IN 46514


Phone: (574) 206-0101


28 Gallon Fresh / Gray Water Holding Tank |T-2872


28 Gallon Fresh / Gray Water Holding Tank |T-2872


Tank Measurements +/- .25" on each measurement due to manufacturing process

VIEW CAD DRAWING DUE TO DESIGN

Average tank thickness .219 or 7/32" thick (just under 1/4")

NO Installed Fittings - Tank is BLANK
We offer Uniseal Fittings - Class A Customs does not sell Spin Weld Fittings.








Class A Customs
1130 County Road 6 West
Elkhart, IN 46514


Phone: (574) 206-0101


36 Gallon Fresh / Gray Water Holding Tank | T-3687

 Tank Measurements +/- .25" on each measurement due to manufacturing process

VIEW CAD DRAWING DUE TO INTRICATE DESIGN

Average tank thickness .219 or 7/32" thick (just under 1/4")

Installed Fittings See Photos
One) 1.5" Female NPT Fitting - fitting is sealed to use remove membrane with razor knife
Three) .5" Female NPT Fitting - fitting is open

www.classAcustoms.com







Class A Customs
1130 County Road 6 West
Elkhart, IN 46514


Phone: (574) 206-0101