Heng's 90110-C1DL Thermal Pane Lid for 70000 Series Vortex Vents - White








Heng's Mini RV Roof Vent 17511-C1G and 18511-C1G









Aerodynamic Design Lid Color White
Screen Removable, strong, fine mesh screen
Handle Low Profile Plastic Manual Crank

Rough Cut-out Opening Dimensions (this is the hole you will need in your roof) 14.5” X 14.5”
Roof Flange Galvanized Steel with Mill Finish

Exterior Mounting Flange Dimensions (sits on the top of your unit) 16.5” X 16.5”
WARNING All Vent Metal Flanges are VERY SHARP use caution when touching

Available Inside Garnish Shroud Sizes 1" / 3" / 4" / 5" / 6" Vertical Leg (How far up into your ceiling it goes)

1.25” Wide Mounting Flange (trim you see inside on the roof)
Color White

No Mounting Hardware


Class A Customs
1130 County Road 6 West
Elkhart, IN 46514

Phone: (574) 206-0101








14" RV Roof Vent Garnish Rings
If you already have a garnish that you are comfortable re-using you do not need to purchase a unit with a garnish ring. Be sure to check the thickness of your roof to determine the correct size garnish ring to purchase with your roof vent.

Heng's Part # 90090
1” OEM Inside Garnish Shroud Color White 13" x 13" x 1 ⅛” Vertical Leg (How far up into your ceiling it goes) 1 ¼” Wide Mounting Flange (trim you see inside on the roof)

Heng's Part # 90092
3” OEM Inside Garnish Shroud Color White 13" x 13" x 3” Vertical Leg (How far up into your ceiling it goes) 1 ¼” Wide Mounting Flange (trim you see inside on the roof)

Heng's Part # 90094
4” OEM Inside Garnish Shroud Color White 13" x 13" x 4” Vertical Leg (How far up into your ceiling it goes) 1 ¼” Wide Mounting Flange (trim you see inside on the roof)

Heng's Part # 90144
5” OEM Inside Garnish Shroud Color White 13" x 13" x 5 ¼” Vertical Leg (How far up into your ceiling it goes) 1 ¼” Wide Mounting Flange (trim you see inside on the roof)

Heng's Part # 90146
6” OEM Inside Garnish Shroud Color White 13" x 13" x 6” Vertical Leg (How far up into your ceiling it goes) 1 ¼” Wide Mounting Flange (trim you see inside on the roof)







Heng's Brand Escape Hatches
The current design of Heng's brand escape hatches will not match older style Heng's escape hatches.



Heng's purchased the Jensen/Elixir brand name some years ago.



The following part numbers and design of the escape hatches are the only Heng's style we carry.


Ventline no longer makes escape hatches, the sizes and hinge assembly are not the same as Heng's, Elixir or Jensen brand, you can not put a Heng's lid on a Ventline escape hatch.



How are Escape Hatches Measured?
The name of the Heng's escape hatches are shortened names to easily identify the escape hatch, it is not the cut-out measurement or the flange measurement.

You will need to verify your cut-out dimension to accurately find the escape hatch you are needing.



Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
Phone: (574) 206-0101





13 x 20 Escape Hatch by Heng’s Part #  31121-C2 - This Escape Hatch has a Plastic Frame
Rough Cut-out Opening Dimensions (this is the hole you will need in your unit)  14 ¼”  X 21"
Exterior Mounting Flange Dimensions (sits on the top of your unit) 16 ¾”  X 23 ¾”  

Lid Measurements 15 ½” x 22 ½”
Lid Only Part # 90007-C1


15 x 22 Escape Hatch by Heng’s Part # 58621-C2
Rough Cut-out Opening Dimensions (this is the hole you will need in your unit) 17 ⅜” X 24 ⅝”   
Exterior Mounting Flange Dimensions (sits on the top of your unit) 19"  X 26 ½”

Lid Measurements 18” x 25”
Lid Only Part # 90008-C1




Rough Cut-out Opening Dimensions (this is the hole you will need in your unit)  19 ¼ "  X 26 ¼ "   
Exterior Mounting Flange Dimensions (sits on the top of your unit) 21"  X 28"

Lid Measurements 19 ½” x 26 ⅜”
Lid Only Part # 90088-C1


Rough Cut-out Opening Dimensions (this is the hole you will need in your unit)  21 ¼ " x 21 ¼ "  
Exterior Mounting Flange Dimensions (sits on the top of your unit) 23"  x 23"

Lid Measurements 21 ½” x 21 ½”
Lid Only Part # 90129-C1

26 x 26 Escape Hatch by Heng’s Part # 68631-C2
Rough Cut-out Opening Dimensions (this is the hole you will need in your unit)  25 1/2" x 25 1/2"
Exterior Mounting Flange Dimensions (sits on the top of your unit) 27 ½ "  x 27 ½ ”

Lid Measurements 26” x 26”
Lid Only Part # 90014-C1



 Heng's "Curl" Style Hinge







Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
Phone: (574) 206-0101






on
Labels:

RV Chrome Table Leg Recessed and Flush Mounted classAcustoms




Chrome RV Table Leg
Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
 
Call Us: (574) 206-0101

on
Labels: ,

SUPERFLEX Alpha System Rubber Roof Class A Customs Elkhart Indiana







Class A Customs Available Membranes:
5
6
PVC - Smooth Both Sides - Color White on both sides
7
8
TPO - Smooth & Frosted Side - Color White on both sides
9
10
EPDM - Smooth & Textured Side (texture varies) - Color White on both sides
11

12
13
Membrane Ships Folded Depending on size of kit you will get one or two boxes (glue / membrane)
14

15
16
Membrane Length / Width It is recommended to get a size that is longer / wider than your unit due to possible curve of the roof, raised or lowered areas, removing the excess is much better than not having enough.
17

18 19

20
21
22

INSTALLATION - Printable Instructions Here
23

24

25
 
26
Membrane must be installed onto clean wooden surface, do not install on top of existing membrane, glue, etc.
27
1. Router all vent and accessory openings. Sand all openings, seams, and edges to a smooth finish. Remove all debris off roof with air hose.
28
29
2. Apply seam tape (2” minimum width) evenly onto roof and sidewall to cover any sharp edges, it is required that seam tape be used to avoid edge splits. (We do not provide seam tape due to different sized needed)
30
31
3. Make sure all screw heads and surfaces are smooth and level throughout, raised screws will snap and puncture membrane and is not covered under warranty.
32
33

34
35
As soon as possible, while on top of clean unit remove membrane from box, do not drag over edge of unit.
36
1. Do Not allow membrane to touch ground or dirty surfaces.
37
2. Do Not allow membrane to touch sharp objects or surfaces, including lifted screw head and edges. 3. Do Not drag the membrane as this can cause punctures and tears which is not covered under warranty.
38
39
4. Membrane can be glued either side down. Single-Ply membranes are the same color throughout.
40

41
42
Membrane Installation
43
1. Cut the membrane to fit roof length with an excess of at least 6” front and rear.
44
2. “Bed Sheet” the membrane. That is, fold it in half so half of the roof is exposed.
45
3. Apply adhesive in a wet film thickness of 8-10 mils with a short-napped paint roller to the exposed half of the roof. (1 gal. will cover approximately 160-200 sq ft.) brush can be used but is more difficult. 4. Lay the roof membrane over the wet adhesive, the membrane needs to be adjusted both in width (side to side) and length (front to rear) to ensure the membrane is as flat as possible before the squeegee process. Let surplus material drape over the side of the unit for perimeter finishing.
46
5. Remove all air pockets and wrinkles with a squeegee (gray neoprene head will not streak), linoleum roller; press firmly working from the center outward toward the edges, do not be on the roof during this time.
47
48
6. All wrinkles must be removed at this point for a quality installation. The roof will tighten and conform as the adhesive cures.
Post settings Labels TPO Roofing,RV Roof,PVC Roofing,EPDM RV Roofing, No matching suggestions Published on 8/8/22 12:31 PM Links Location Search Description Options Post: Edit
on
Labels: , , ,

Alpha System Rubber Roofing Class A Customs Elkhart IN







Class A Customs Available Membranes:
5
6
PVC - Smooth Both Sides - Color White on both sides
7
8
TPO - Smooth & Frosted Side - Color White on both sides
9
10
EPDM - Smooth & Textured Side (texture varies) - Color White on both sides
11

12
13
Membrane Ships Folded Depending on size of kit you will get one or two boxes (glue / membrane)
14

15
16
Membrane Length / Width It is recommended to get a size that is longer / wider than your unit due to possible curve of the roof, raised or lowered areas, removing the excess is much better than not having enough.
17

18 19

20
21
22

INSTALLATION - Printable Instructions Here
23

24

25
 
26
Membrane must be installed onto clean wooden surface, do not install on top of existing membrane, glue, etc.
27
1. Router all vent and accessory openings. Sand all openings, seams, and edges to a smooth finish. Remove all debris off roof with air hose.
28
29
2. Apply seam tape (2” minimum width) evenly onto roof and sidewall to cover any sharp edges, it is required that seam tape be used to avoid edge splits. (We do not provide seam tape due to different sized needed)
30
31
3. Make sure all screw heads and surfaces are smooth and level throughout, raised screws will snap and puncture membrane and is not covered under warranty.
32
33

34
35
As soon as possible, while on top of clean unit remove membrane from box, do not drag over edge of unit.
36
1. Do Not allow membrane to touch ground or dirty surfaces.
37
2. Do Not allow membrane to touch sharp objects or surfaces, including lifted screw head and edges. 3. Do Not drag the membrane as this can cause punctures and tears which is not covered under warranty.
38
39
4. Membrane can be glued either side down. Single-Ply membranes are the same color throughout.
40

41
42
Membrane Installation
43
1. Cut the membrane to fit roof length with an excess of at least 6” front and rear.
44
2. “Bed Sheet” the membrane. That is, fold it in half so half of the roof is exposed.
45
3. Apply adhesive in a wet film thickness of 8-10 mils with a short-napped paint roller to the exposed half of the roof. (1 gal. will cover approximately 160-200 sq ft.) brush can be used but is more difficult. 4. Lay the roof membrane over the wet adhesive, the membrane needs to be adjusted both in width (side to side) and length (front to rear) to ensure the membrane is as flat as possible before the squeegee process. Let surplus material drape over the side of the unit for perimeter finishing.
46
5. Remove all air pockets and wrinkles with a squeegee (gray neoprene head will not streak), linoleum roller; press firmly working from the center outward toward the edges, do not be on the roof during this time.
47
48
6. All wrinkles must be removed at this point for a quality installation. The roof will tighten and conform as the adhesive cures.
Post settings Labels TPO Roofing,RV Roof,PVC Roofing,EPDM RV Roofing, No matching suggestions Published on 8/8/22 12:31 PM Links Location Search Description Options Post: Edit
on
Labels: , , ,

Metal Folding Tire Carrier 136203 classAcustoms











Metal Folding Tire Carrier 136203

Heavy-duty welded steel construction
Powder Coated to Resist Rust
“Universal Bumper Mount” bolts easily to 4-1/2” maximum square bumper with hand tools (no drilling).
Allows trouble-free access to rear compartment.
Fits virtually all lug hole patterns and even deep dims
Includes all mounting hardware, corrosion resistant
Items are purchased in bulk quantities so no retail box.

Class A Customs
1130 County Road 6 West
Elkhart, IN 46514
 
Call Us: (574) 206-0101


on
Labels:

Ventline BVD043431 White Replacement Screen classacustoms

Ventline BVD043431 White Replacement Screen

This fits Ventline RV Roof Vents only - this will NOT fit Heng's Brand Roof Vents


Ventline 14" Ventadome Roof Vent 12 volt FAN White Lid




Class A Customs
1130 County Road 6 West
Elkhart, IN 46514

Phone: (574) 206-0101


on
Labels: ,
Subscribe to: Posts (Atom)