8 1/4” x 10” GREASE FILTER 12V RV Range Hood Aluminum Heng's JRP1204B classAcustoms


 Heng's has redesigned the part # J116AWH-C Exterior Wall Vent
used with ducted range hoods.


 Color of vent has an off white, creamy color



 

Flap locks with push tabs


To install the vent you will need to remove the outer cover, be sure to press in the tabs on both sides to release the front cover.




  Be sure to press in the tabs on both sides to release the front cover, bend tabs in do not try to force the cover off or you will break it.


 3/4" is the size of the insert that will go into the trailer wall
If this does not reach through the trailer wall you can trim the inside of the wall with wood or metal.

2 1/2" overall Width of unit including the cover


 12 11/16" is the overall Length of the unit


6 1/16" is overall Height of unit

Screw holes are inset 1/2" from outer edge (this does not include cover)
This is a new design and screw holes may not match your current unit.

NEW DESIGN J116AWH-C Heng's Range Hood Exterior Exhaust Vent Off White J116AOW-C

Class A Customs
1130 County Road 6 West
Elkhart, IN 46514


Phone: (574) 206-0101





PLEASE NOTE:

These are 12 volt Range Hoods

You CAN NOT use them in a house, that is 110 volt and will damage the unit.



RV 12 Volt Range Hood Vent Installation Instructions Heng's Ventline Elixir classacustoms


Range Hood - Slope Style like Elixir, Jensen and Ventline.
12 Volt - You can not put this in a house as that is 110 volt, you will damage the unit.
Washable Grease Filter Included
Underside Light, 10W maximum bulb, Helps you see while cooking.
You choose Ductless or Ducted style range hood.

Measurements:
The overall size of this unit is choose 20" / 22" / 24" wide x 18" deep x 5 1/4" tall.
The slope nose allows installation of this unit with cabinets from 12" - 18" deep.
The hole size for the outside duct is 10" x 3".

Photos are of Heng's Brand Range Hoods in Stainless Steel
























RV Range Hood Cooking Exhaust Fan 12 volt MOTOR Heng's 90044-C


For the 12 volt Range Hoods by Heng's
If you are needing a 12 volt Vent Motor that is Part # 90037-C1 which we also sell.

**12 VOLT POWER ONLY 110/115/220 volt such as in a house or generator will damage the unit**
Shaft "half-moon" or "D" shaft - 1/8" Diameter x 1/2" Long
AMP 1.6








**12 volt ONLY 110/115/220 volt such as in a house or generator will damage the unit**


Stainless Steel 300 series 22 gauge
White or Black Durable Powder Coated Paint Resists Scratching and Chipping
Metal, Washable Grease Filter
Two front panel rocker switches for control of the light and fan


Ductless Style Recirculates air
Ducted Style vents out the back of range hood Exterior Duct 10” x 3”


Overall Measurements
20” Range - 20" w x 18" d x 5 ¼” t
22” Range - 22" w x 18" d x 5 ¼” t
24” Range - 24" w x 18" d x 5 ¼” t


Slope nose design allows installation under cabinets from 12"-18" deep



Class A Customs
1130 County Road 6 West
Elkhart, IN 46514


Phone: (574) 206-0101