WT-3469 | WASTE TANK 34 Gallon Water Holding Tank WT-3469
Waste Water Tank Used for Human Waste or Gray Water - DO NOT use for fresh or drinking water
Non-pressurized Tank all tanks we carry must be vented (allow air in/out during use), Plumbing Example
Waste Or Gray Water Use great for rvs, food vendors, tiny houses, overlanding and extra waste water storage
Seamless One-piece seamless construction, no seams to burst Average tank thickness: .219 or 7/32" thick (just under 1/4")
Resistant Stain, Corrosion and Rust Resistant
Color Black in color so tank is easily identified as a waste tank
Made With
Recycled Medium Density Polyethylene (MDPE) Resin - glues do not stick
to this material and easily cleaned. - Because product is recycled and
intended for waste use it is not tested for safety of drinking or
gardening water supply.
Installed Outlet Options
3” ABS Female Pipe - outlet can not be moved
Inlet & Vent
Class
A Customs Waste Water Tanks only come with the outlet the end user will
determine where the inlet and vent will need to be placed and install.
Overall Measurements - See Photos
54.75" x 28.38" x 6.63"
Installed Outlet Options
3” ABS Female Pipe - outlet can not be moved
1.5" ABS Female Pipe - outlet can not be moved - Due to the smaller outlet this tank is for dirty water from shower, handwashing, dish-washing - DO NOT use for human waste
Connecting Pipe & Dump Valve
From
the ABS outlet that is installed in the tank run PVC Pipe or ABS Pipe
to the outside of the trailer, a dump valve is added to the piping.
Pipe
is connected to the ABS installed fitting in the tank with glue. You do
not need to tighten the clamp that is on the ABS Fitting, this is used
when the ABS fitting is installed into the tank and does not help secure
your piping, over-tightening this clamp will damage ABS fitting and
tank
Dump Valves
Dump Valves do not
hook directly to the ABS fittings, the ABS Outlets are female fittings
and the dump valves are also female fittings, you will need a pipe to
fit inside of the outlet and dump valve in order to make the connection.
We do not sell glues, example only Oatey 4-fl oz Green PVC/Abs Transition Cement
Inlet & Vent Installation
Class
A Customs Waste Water Tanks only come with the ABS outlet installed,
the end user will determine where the inlet and vent will need to be
placed and install.
Grommets
are not food safe so can only be used for Gray or Waste Water use they
are available in sizes 1.5" and 3", no adhesives are needed for use.
Uniseal Fittings
are food safe and can be used for Fresh, Gray, or Waste Water use, they
are available in size .5" to 3", no adhesives are needed for use.
Use correct size hole saw bit in order to drill a hole in the tank, smooth tank edges, and place Grommet or Uniseal in hole. Piping is then placed into fitting with no glues or adhesives necessary.
Mounting & Bracing
Some
of the Class A Customs Waste Water Tanks are built with a "lip" on the
tank. Tanks can be hung by this lip, it is recommended to make a shelf
to slide the tank lip into.
You will need to brace the tank on all sides to prevent movement of the tank.
Brackets or Strap Systems Due to the variety of installations we do not carry brackets or bracing systems. Do Not hang by ratchet strap, this is too thin and will not adequately support tank.
Water Tank Monitor System
To check fluid levels, press and hold the button designated for the tank and read the level indicators on the panel. Sometimes, residue on the sides of a tank, or water with a low mineral content will give a false reading.
Check the levels occasionally when you are sure of a tank’s contents and compare it to the reading on the monitor panel.
4 Probes per tank needed
3/8" drill bit needed Measure
and mark installation points before drilling. After drilling be sure to
remove any burs from hole. Do not over-tighten probes.
Tank
harnesses included with monitor panel. Customer will need to provide
the extra wiring to run from the tank harness to the monitor panel. View
wiring diagram for wire gauges ( 20 AWG / 14 AWG)
